craftsman power washer how to start

Continue pressing until water begins to. Attach one end of the pressure hose to the water pump of the washer and another end to the High-pressure spray gun.

Craftsman Pressure Washer Featuring Quiet Sense Pressure Washer Electric Pressure Washer Craftsman

Right position of craftsman pressure washer matters.

. Before replacing an ignition coil confirm that the spark plug is working properly. Almost brand new Craftsmen 163cc w Ready Start carb. Diagnosing why the Craftsman Power Washer would not start and the easy simple fix also discovered the pump outlet extension was cracked and profusely leakin.

Craftsman Pressure washer wont start. It may say on or off. 01 - Spark Plug.

Any loose connection may cause short-circuit and fire. Make sure its tighter. Connect the inlet hose to the main water supply and pressure washer inlet.

Inspect the spark plug for signs of wear or damage. Find The Cheapest Prices Here. You heard it right.

These simple steps can make all the difference in the perfo. To determine if the spark plug is defective use a spark plug. Next connect the male end of the high pressure hose that comes with the unit into the water.

The first thing that you have to know when you learn how to start Briggs and Stratton power washer is that it needs to be warmed up and set up before you can use it. The first thing you should do when using a pressure washer is turn it on. This is done by pressing the power button on the front of the machine.

Pull the trigger on the handle to spray the water and soap mixture. Below is the step-by-step guide to starting your Craftsman gas-powered power washer. Pour the approved detergent into the soap reservoir and then turn the power switch to the On position on the power washer or start the motor by pulling on the T-handled cord and then flip the switch.

Ad Shop Genuine Craftsman Parts at Sears PartsDirect. Using your hand attach the hose tightly to the pressure by way of the water inlet which is clearly labeled. This is the type with the B S engine that doesnt need to be primed or choked.

Tried with the spray trigger off. Press and hold the trigger on the sprayer gun to clear any air or debris. The next step is to attach the garden hose to the water supply.

Make sure the water strainer is free from debris and place it in the right position. Before you start your craftsman pressure washer. We will also discuss some basic steps to guide you deeply.

If its faulty replace it. Craftsman parts - manufacturer-approved parts for a proper fit every time. Left a little in over winter and filled with fresh.

UghAlthough I didnt really find anything wrong or plugged up in the carb - basic. Turn the water supply on starting the flow of water into your washer. Always place your pressure washer on a flat surface.

Make sure the pressure washer is on a flat surface and check to make sure the water strainer is in place and free of debris. If the ignition coil is defective the Pressure washer will not start. If youve already confirmed this test the ignition coil on an ignition coil tester.

The pressure washer will then come on and display its status. It works best to point the gun at an angle if you are using high. If it says off press the power button again until it changes to on.

If the porcelain insulator is cracked an electrode is burned away or damaged or there is heavy carbon buildup at the electrode replace the spark plug. Make sure its being placed on a levelled surface. Step no 1.

Attaching hose to water supply. Set switch to 1 connected water line discharged air made sure there was a steady water stream left the spray trigger on while I pulled the starter. So the next steps will involve setting up the machine.

This video will show the startup procedure for a gas powered pressure washer. Make sure the connector plug of electricity is perfectly connected to the power hub. How to Start Briggs and Stratton Power Washer Steps Video Heres how to do that.

The ignition coil sends voltage to the spark plug while the engine is running. Positioning is an extremely important parameter. Connect a garden hose to the washer and the other end to your water supply.

Put your pressure washer outdoors near a water supply. Watch this video to learn how to properly vent air out of a pressure washer before turning it on.

Pin On Products